Dom > Novice > Vsebine

Galvanizacija vs Sherardizing

Sep 22, 2021

Sherardiziranje is also called thermal diffusion galvanizing (TDG), vapor galvanizing or  dry galvanizing, and it's is a specific process involving zinc powder and proprietary chemicals. Steel workpieces are cleaned before zinc coating process, and the cleaning process covers degrease and sandblasting, and then they are tumbled in a heated drum at temperatures slightly less than hot-dip galvanizing (680 - 825 degree F) so that matte gray HDG-like intermetallic alloy layers are produced.

Sherardized Rectangular Tubes (2).jpg
Galvanized Angles.jpg

Medtemvroče pocinkanje (HDG)is a process of handling steel workpieces to go through a series of pretreatment, and then dipping  steel parts into the molten (830 F) zinc bath with, and workpiece is lowered into the kettle at an angle which allows air to escape from tubular shapes or other corners. During the dipping process, the iron metallurgically reacts with the zinc to form a series of zinc-iron intermetallic layers and an outer layer of pure zinc.



What's the difference between sherardizing and HDG?

Postopek vročega pocinkanja ne povzroči krhkosti vodika, vendar bo njegova predhodna obdelava, kislo luženje povzročilo krhkost. HDG ima običajno bolj grobo površino kot sherardiziranje, sherardizacija pa se običajno uporablja za dele, ki zahtevajo močno protikorozijsko zaščito in strožjo toleranco pri sestavljanju.Vroče pocinkani deli are widely used in infrastructure like motorway railing systems, cable racking system in tunnel and subway, solar energy, steel structure for bridge and construction. Sherardizing is widely used for fasteners and steel works which requires high precision assembly, and sherardizing production capacity is not as high as hot dip galvanizing because it's constrained by the tumbling drum.

Advantages of Sherardizing 

√  No risk of acid deposition around welded area

√  Complete elimination of hydrogen embrittlement

√  No need for re-threading or further fitting operations

√  Readily accepts top coats, no need for expensive primers

√  Withstand a fair measure of high industrial pollution and rough handling

√  Suitable for acting as a pre-coating for paints, powder coatings and rubber bonding

√  Hardest of all zinc coatings compared with hot dip galvanization, spin galvanization and zinc plating

√  Uniform coating, ideal for smaller and irregularly shaped items without unfavorable peak build up on 

    corners or on threads

√  Consists exclusively of intermetallic phase Fe-Zn, which permits the control of case depth and 

    ensures high corrosion resistance

√  Lower temperature process range, which avoids parts losing their mechanical properties and shapes 

    such as spring steels and fasteners

Zaradi prednosti sherardizacije so številni jekleni izdelki, ki zahtevajo natančno montažo in dobro protikorozijsko zaščito, -korozijsko zaščiteni, kot so pritrdilni elementi,kovinski nosilci po meri, jeklene konstrukcije in jeklenih pragov.

Pomanjkljivost vročega cinkanja

√  Pocinkane vodovodne cevi lahko sproščajo svinec v vodovod

√  Rough coating surface, and spikes tend to remain at the end of workpiece during lifting process 

    which je treba med pregledom odstraniti

√  Due to the deposition of zinc, undercut nuts is required for fitting purpose, and the heat involved in 

    the galvanization process limits the grade of fastener

√  Due to its rough surface nature, it requires very strict control of sandblasting for uniform 

    galvanization surface.

Skratka, največja pomanjkljivost vročega pocinkanja je njena neenakomerna površina, ki bi lahko povzročila težave pri montaži, zlasti pri pritrdilnih elementih. Prevladuje vroče pocinkanjeobdelava kovinske površinezainfrastrukture, telekomunikacije, kmetijstvo, ribogojstvo, sončna energija, rudarstvo in tunel.

Za vizualizacijo osnovnih dejstev o različnih cinkovih premazih se lahko obrnete na spodnjo tabelo za jasnejše razumevanje stroškov, znakov premaza in ustreznih standardov.

Stroški

Sherardiziranje

Zinc   Plating 

Hot Dip   Galvanization

Srednja raven

nizka

Mid   Level

Britanski standardi EU

BS   EN IS0 17668:201                        

BS7371 del 8:1999

BS1706/BS   EN 12329:2000
BS 3382 DEL 2 za pritrdilne elemente

BS   729/BS EN ISO 1461                                               

BS7371 part 6:1988 for fasteners 

Debelina cinkove prevleke

15-80μm or more

5-25μm

30-200μm

Adhesion 

Odlično, zlitina s substratom

Slabo, brez zlitine s substratom

Dobro, nekaj zlitine s substratom

Enotnost

Excellent, vapour deposition ensures uniformity, ideal for iregularly shaped, recessed and threaded components and tight tolerance for precision assembly. 

V odtočnih mestih se nabira slab staljen cink

Slabo odlaganje cinka na vogalih, navojih in luknjah

Odpornost proti obrabi

Excellent, hardest of the zinc coating due to iron alloy. The coating can only be removed by chemicalor  mechanical solution.

Good, can withstand forming but mainly applied to finished components. 

Good, a tough durable coating but can't stand forming

Postpovršinska obdelava

Excellent, forms an excellent iron zinc alloy which accepts top coats without the need for primers or surface   preparation. Top coating like paints, powder coatings, Ecoating and rubber bonding is popular choice.

Slabo, zahteva nadaljnjo obdelavo za zagotovitev oprijema

Poor, requires pretreatment like   sandblasting with extra attention to the blasting force, or suitable primer to ensure adhesion

Krhkost vodika

Brez tveganja, saj ni uporabljena kislina, postopek pa je suh in ne vsebuje virov vodika.

High risk, due to acid use for pickling process. 

High risk, due to acid use for pickling process. 

Color  

Matte   grey

Popular   colors are yellow/gold, clear/blue, black and green.

Svetla in sijoča, toda v enem letu bo prestala do enakomerne dolgočasno siv videz

Ure s solnim pršenjem

Moderate coating thickness could reach 720 hours, and thicker coating could reach 1000   hours. 

Z dodatkom pokrivnih premazov, znanih kot kromat, in standardni minimum je 96 ur.

For   moderate HDG thickness requirement, it shall pass 480   hours, and for high corrosive enviornment, thicker   coating is required for passing 720 hours.



Pošlji povpraševanje